Seth Thomas Ship's Bell Yacht Clock c1910

Significance

A Seth Thomas Ship's Bell Clock with a stand c1910. A functional clock, not domestic, used on ships and yachts for general timekeeping, usually on a wall, secured top and bottom. Apparently quite rare as few survive marine service. The strike pattern is for the ship's watch. Used on military and merchant vessels.

It is claimed that a Seth Thomas clock was recovered from the wreck of the USS MAINE 1895 and presented to Franklin Delano Roosevelt when he was (Assistant) Secretary of the Navy 1913-1919.

Description

A balance wheel and lever escapement, presumably reasonably accurate given its purpose.

"Ship's Bells struck through the double strike system mark off the series of four hour watches that make up the sailor's day. Each four hour watch is divided into half hour periods tolled from one through eight bells. When the chiming gets out of sequence the clock has a "Lever" that makes it easier to coordinate the chime sequence with the time without moving the hands. The clock runs for one day, and for best accuracy it should be wound every twelve hours." http://landandseacollection.com/id806.html



eBay Australia; Tasmania. Apparently rare.

The bell over ship's clock with a detachable stand.

The printed paper back, a little the worst for wear, and mounting points.






As it would be used onboard a ship. Not my clock.

The printed paper on the back. Not my clock.




Comments

Post a Comment

Popular posts from this blog

Seiko Vibron Tuning Fork Clock c1960s-70s

Image
Significance A Seiko clock using a tuning fork and mechanical movement, powered by a battery and single transistor drive. Made in Japan in the 1960s to early 70s in the brief period after transistors became available and before they were replaced by quartz clocks. Description The Seiko Vibron VBZ-208 is an electronic-mechanical, 6-jewel clock that uses a 150 Hz vibration, H-shaped, double-ended tuning fork. The tuning fork element was developed by Seiko to be virtually immune to changes in temperature being made of a special alloy. A single transistor switch drives a solenoid to magnetically excite the tuning fork. The other end of the tuning fork has two magnets, along with a rotating disk that constitutes a synchronous motor that then drives the gears set to the hands. The movement offers extremely high timekeeping precision. The clock is big and heavy, around 2 kg, indicating it was probably quite expensive when new. The face is metal rather than plastic with a metal finish.
Read more

Lenzkirch Wall Clock 1 Million Fusee late 1890s

Image
Significance A Fusee Lenzkirch Wall Clock, 1 Million series 21 movement, late 1890s. Lenzkirch used mass-production to make high-quality clocks in the Black Forest region of Germany from 1860 to 1932. A fusee movement in the 1890s is unusual in the 1890s as steel springs had improved from the 1850s that were sufficiently accurate for most makers. However, a few quality makers continued with fusee as well as improved springs. Fusee were used in most marine chronometers until they became obsolete. Lenzkirch clocks have few maker's marks, but the "1 Million" above the serial number is characteristic, along with 21 for the movement series. Description A high quality 300 mm wall clock with a short pendulum inside the case with a fusee movement. The dial surround is solid timber. The movement frame is a solid brass sheet. Local pickup through online Gumtree classifieds. Notes http://antique-clock.com/about/lenzkirch http://www.clockguy.com/SiteRelated/SiteRefere
Read more

Suko Artempo Handless Clock c1990

Image
Significance Modern quartz clocks can be cute too! A novelty clock. Suko made a number of similar designs using the same principal. Description A novel design. Italian I think. The dial rotates around the spindle with the time indicated at the spindle. I think the white "hands" have been added as they are not on other clocks. A year 2000 clock is available but I have yet to get one. Source Ebay, Melbourne, Australia.
Read more